Manual.ly Logo

Benning DUSPOL digital Kilavuz

5,0 · 3 Puanlar

PDF kılavuzu · 91 Sayfa

Türkçe

M: QW-35-FL
sayfa

/ 91

Loading...
f6617ca8dc3778b540c3f3c17acb02139854 page b
02/ 2019
DUSPOL
®
digital
8
sure a capacitive coupling to earth.
- Apply the probe tips L1/-
2
and L2/+
3
to two external
conductors (phases) and check whether the external con-
ductor voltage of e.g. 400 V is applied.
- A clockwise phase sequence (phase L1 before phase L2)
is given, if the green LED „►“ of the phase sequence in-
dication
L
and the symbol of the phase sequence
indication
P
light up on the LC display
6
.
- A counter-clockwise phase sequence (phase L2 before
phase L1) is given, if the green LED „◄“ of the phase
sequence indication
L
and the symbol of the phase
sequence indication
P
light up on the LC display
6
.
- The phase sequence test always requires a countercheck
with the probe tips L1/-
2
and L2/+
3
being inverted dur-
ing which the phase sequence must change.
Note:
The phase sequence test can be carried out in an earthed
three-phase mains from 400 V - 900 V, 50/60 Hz (phase to
phase) on. Protective clothing and insulating conditions on site
might impair the function.
8. Continuity test (gure I)
- The continuity test must be carried out on system parts
which are free of voltage. If necessary, capacitors have to
be discharged.
- Apply the two probe tips L1/-
2
and L2/+
3
to the system
parts to be tested.
- In case of continuity (R < 100 kΩ), an acoustic signal is
emitted and the yellow LED Ω
M
for continuity lights up.
- If a voltage is applied to the test point, the voltage tester
automatically switches over to the voltage test function
and indicates this function.
9. Resistance measurement (gure J)
- The resistance measurement must be carried out on sys-
tem parts which are free of voltage. If necessary, capaci-
tors have to be discharged.
- Short-circuit the probe tips L1/-
2
and L2/+
3
and press
the push-button
7
of the display handle L2
9
once until
the kΩ symbol and „Ohm“ are shown on the LC display
6
. Display: „OL“ stands for a measured value which is
outside the measuring range.
- The resistance measurement function is active for approx.
10 seconds.
- Apply the probe tips L1/-
2
and L2/+
3
to the system
parts to be tested in order to measure resistances from
0.1 kΩ to 300 kΩ.
Note:
If required, it is possible to carry out a null balance with the
resistance measurement function being activated. For this pur-
pose, short-circuit the probe tips L1/-
2
and L2/+
3
and press
and hold the push-button
7
of the display handle L2
9
for
approx. 2 seconds until „0.0“ kΩ is shown on the LC display.
10. Diode test (gures K/L)
- The diode test must be carried out on system parts which
are free of voltage. If necessary, capacitors have to be dis-
charged.
- Short-circuit the probe tips L1/-
2
and L2/+
3
and press
the push-button
7
of the display handle L2
9
twice until
the diode symbol and „diod“ are shown on the LC
display
6
. Display: „OL“ VDC
- The diode test is active for approx. 10 seconds.
- Apply the probe tip L1/-
2
to the cathode and the probe
tip L2/+
3
to the anode of the diode to determine the con-
ducting-state voltage between 0.3 V and 2 V. In case of a
defective (broken down) diode, a voltage value of approx.
0.0 V will be displayed.
- In case of a diode tested in non-conducting direction, the
LC display shows „OL“.
11. Cable break detector (gure M)
- The cable break detector is intended for the non-contact
localization of cable breaks on exposed live lines.
- Switch the voltage tester on by briefly actuating the push-
button
7
of the display handle L2
9
(remains switched
on for approx. 10 seconds!). When the device is switched
on, the display shows „0.0“.
- Fully grasp the display handle L2
9
and pass the detec-
tor
5
over a live line (e.g. a cable reel or a chain of lights)
from the feeding point (phase) in direction of the other end
of the line.
- As long as the line is not interrupted, the yellow LED Ω
M
for continuity is flashing.
- The point of the cable break has been localized as soon as
the yellow LED Ω
M
goes out.
Note:
The cable break detector may grounded power from 230 V,
50/60 Hz (phase to earth) are used. Insulating protective cloth-
ing and site conditions can affect the function.
12. Measuring point/display illumination (gure N)
- The measuring point illumination
4
can be switched on
with the probe tips being open by actuating the push-but-
ton
7
of the display handle L2
9
(1 second).
- The off automatically after 10 seconds
- The background lighting of the LC display
6
is activated
automatically by means of a light sensor
N
.
13. Battery replacement (gure O)
- Do not apply voltage to the device when the battery com-
partment is open!
- Please replace the batteries as soon as the
symbol
is shown on the LC display
6
.
- The battery compartment is located on the back of the dis-
play handle L2/+
9
.
- Unscrew the screw of the battery compartment cover and
replace the used batteries by two new micro batteries
(LR03/AAA).

Yapay zeka ile Benning DUSPOL digital kılavuzunuzla sohbet edin

Benning DUSPOL digital kılavuzunuzdan yapay zeka ile anında yanıt alın

Benning DUSPOL digital hakkında istediğinizi sorun. Yanıtlar bu kılavuzdan gelir ve dayandığı sayfalar belirtilir.

DUSPOL digital Bakim Takvimi

Gerekli Olduğunda
Düşük pil sembolü göründüğünde pilleri değiştirin

LC ekranda boşalmış pil sembolü gösterildiğinde iki adet Micro LR03/AAA pili derhal değiştirin.

Kilavuzda goster (11. sayfa)
Her Kullanımdan Önce ve Sonra
Gerilim yokluğunu kontrol etmeden önce işlevsel test yapın

Güvenliği sağlamak için gerilim test cihazının doğru çalıştığını kullanmadan hemen önce ve sonra kontrol edin.

Kilavuzda goster (8. sayfa)
Uzun Süreli Saklama Durumunda
Saklama sırasında cihazdan pilleri çıkarın

Cihaz uzun bir süre saklanacaksa, hasarı önlemek için pilleri cihazdan çıkarın.

Kilavuzda goster (8. sayfa)
Gerekli Olduğunda
Kasa ve pil bölmesini kuru bir bezle temizleyin

Cihazın dış yüzeyini ve pil bölgesindeki kirleri temiz, kuru bir bezle silin.

Kilavuzda goster (8. sayfa)
M: qwen/qwen3.8-flash

Soru Sor Soru

0/1000

DUSPOL digital'i önerir misiniz?

Evet Hayır
0
User Pic

Dan King

4 ay önce

Bu cihaz için kalibrasyon hizmeti gerekli mi, yoksa atlayabilir miyim?

0
User Pic

Manual.ly

4 ay önce

Kullanıcı geri bildirimlerine göre kalibrasyon hizmetine gerek yoktur. Cihaz, ek kalibrasyon adımları olmadan kutudan çıktığı gibi amaçlanan işlevini doğru bir şekilde yerine getirir.

M: QW-35-FL
M: QW-35-FL
0
User Pic

Jaleel Marquardt

6 ay önce

Ürünü aldığımda pil zaten pakette neden takılıydı?

M: QW-35-FL

Sıkça Sorulan Sorular

A

Uçları kısa devre yaparak ve itme düğmesini üç saniye basılı tutarak işlevsel bir test gerçekleştirin. Zil çalmalı ve tüm LEDler ile ekran segmentleri yanmalıdır. Ayrıca 230 V priz gibi bilinen bir voltaj kaynağı üzerinde de test etmelisiniz.

Bu yanıt yardımcı oldu mu?

A

Evet, probları kısa devre ederek ve Lo U görünene kadar butona üç kez basarak. Bu, 1,0 V ile 11,9 V arasında ölçümlere izin veren düşük voltaj aralığını etkinleştirir, ancak bu modda frekans göstergesi devre dışıdır.

Bu yanıt yardımcı oldu mu?

A

Titreşim motoru, işletim voltajı ile parazit voltajları arasında ayrım yapmaya yardımcı olur. Her iki düğmeyi aktif ederek, reaktif voltajları bastıran ve kondansatörleri boşaltan düşük dahili direnç moduna geçersiniz.

Bu yanıt yardımcı oldu mu?

A

Ekran kolunun arkasındaki pil bölmesinin yerini bulun. Kapağı vidalayın, eski AAA pilleri çıkarın, iki yeni pil takın ve doğru polariteyi sağladığınızdan emin olun, ardından kapağı sıkıca tekrar vidalayın.

Bu yanıt yardımcı oldu mu?

A

IP65 derecesine sahiptir, yani toz geçirmezdir ve su jetlerine karşı korunmuştur. Yağmurda kullanılabilir, ancak suda batırılmamalıdır.

Bu yanıt yardımcı oldu mu?

A

Voltaj 1.050 V AC veya 1.250 V DC'yi aşarsa, ekranda OL gösterilir ve aşırı yük uyarısı için tüm adım-gösterge LEDleri yanıp söner.

Bu yanıt yardımcı oldu mu?

M: QW-35-FL

Avantajlar ve Dezavantajlar

Avantajlar

  • Yük bağlantısı ve titreşim motoru kullanarak işletim voltajı ile parazit voltajları arasında ayrım yapar
  • Süreklilik, direnç, diyot ve kablo kırığı tespiti dahil kapsamlı test yetenekleri
  • Zorlu ortamlarda kullanım için toz ve su jetlerine karşı IP65 koruma ile yüksek güvenlik derecesi
  • Otomatik kendini test fonksiyonu, kullanımdan önce LEDler ve zil gibi tüm bileşenlerin doğru çalışmasını sağlar
  • Yalıtılmış tutuşlara sahip çift kollu tasarım, canlı devre testleri sırasında güvenli tutmayı sağlar
VS

Dezavantajlar

  • Aktifleşmek için minimum 9 V voltaj gerektirir, özel mod olmadan çok düşük güç kaynaklarında kullanımını sınırlar
  • Titreşim motorunun yüksek akım çekimi nedeniyle uzun süreli yük testleri sırasında pil ömrü azalabilir
  • Faz sırası göstergesi sadece 50/60 Hz'de topraklı ağlarda çalışır, küresel uygulanabilirliği sınırlar
  • Pil bölmesi açıkken kullanılamaz, güç erişiminin dikkatli yönetimini gerektirir
  • Aşırı ısınmayı önlemek için maksimum çalışma döngüsü 30 saniye ile sınırlıdır, uzun testler sırasında molalar gerektirir
M: QW-35-FL

Ürün Özellikler

Ölçüm aralığı

1-1000 V

M: QW-35-FL

Ürün Açıklama

Benning Dijital Voltaj Test Cihazı Çanta İle - Profesyoneller için Temel Güvenlik

Benning Dijital Voltaj Test Cihazı Çanta İle, günlük çalışmalarında hassasiyet ve güvenlik talep eden nitelikli elektrikçiler için tasarlanmış sağlam ve güvenilir bir araçtır. DUSPOL dijital olarak bilinen bu cihaz, birden fazla tanı işlevini tek, ergonomik bir ünitede birleştirerek elektrik test ekipmanlarında önemli bir ilerleme temsil eder. Hem voltaj yokluğunu kontrol etme, hem faz sıralarını test etme, hem de kablo kırıklarını bulma konusunda net görsel ve işitsel geri bildirim sağlayarak güvenliğinizi sağlar.

Sezgisel bir LC ekran ve çok seviyeli bir LED gösterge ile donatılmış olan tester, elektrik ortamı hakkında anlık içgörüler sunar. Yüksek doğrulukla 1.000 V'a kadar alternatif akımı ve 1.200 V'a kadar doğru akımı ölçebilir. Titreşim motorunun dahil edilmesi, kullanıcıların işletim voltajı ile parazit voltajları arasında ayrım yapmalarına olanak tanır; bu özellik, yanlış okumalara neden olabilecek saçılma akımlarıyla uğraşırken karmaşık tesisatlarda kritik bir özelliktir. Cihaz, en az 9 V'luk bir voltaj tespit ettiğinde otomatik olarak açılır, böylece bir inceleme sırasında sürpriz yaşamazsınız.

Kullanıcı güvenliğini üst öncelik olarak tasarlayan tester, yalıtılmış tutamaklara sahiptir ve voltaj yokluğunu onaylamak için özel iki kutuplu bir testi gerektirir; bu da DIN EN 61243-3 gibi sıkı güvenlik standartlarına uyum sağlar. Dahili kendini test fonksiyonu, her kullanımdan önce zilin, LEDlerin ve ekranın bütünlüğünü doğrular, sonuçlarınızda size güven verir. Ayrıca, düşük voltaj modu, standart şebeke voltajı kontrollerinin ötesinde çeşitli uygulamalar için onu çok yönlü kılan 1,0 V'a kadar hassas ölçümler sağlar.

Paket, instrumentin nakliye sırasında tozdan, neme ve fiziksel hasardan koruyan dayanıklı bir taşıma çantasını içerir. IP65 derecesine sahip olan tester, su jetlerine ve toza karşı dirençlidir; bu da onu zorlu endüstriyel ortamlarda veya açık hava koşullarında kullanıma uygun kılar. Düzenli bakım basittir; temizlemek için sadece kuru bir bez ve standart AAA pilleri kullanarak zamanında pil değişimi içerir. Elektrik tanıları için kapsamlı bir çözüm arayan profesyoneller için, Benning Dijital Voltaj Test Cihazı Çanta İle, işlevsellik, dayanıklılık ve güvenliği birleştiren güvenilir bir yol arkadaşı olarak öne çıkar.

M: QW-35-FL

© Copyright 2026 Manual.ly