Manual.ly Logo

Dremel Stylo+ 2050 Kilavuz

4,0 · 4 Puanlar

PDF kılavuzu · 164 Sayfa

Türkçe

M: GO-GEM-FL-25
sayfa

/ 164

Loading...
9c8eef9c2a66ff041a179419530e90183af9 page 9
SAFETY INSTRUCTIONS FOR
ALL OPERATIONS
SAFETY WARNINGS COMMON FOR GRINDING,
SANDING, WIRE BRUSHING, POLISHING, CARVING OR
ABRASIVE CUTTING-OFF OPERATIONS
a. This power tool is intended to function as a grinder,
sander, wire brush, polisher, carving or cut-off tool.
Read all safety warnings, instructions, illustrations

Failure to follow all instructions listed below may result
in electric shock, re and/or serious injury.
b. 
designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
c. The rated speed of the grinding accessories must
be at least equal to the maximum speed marked on
the power tool. Grinding accessories running faster
than their rated speed can break and y apart.
d. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories cannot
be adequately controlled.
e. The arbour size of wheels, sanding drums or any

collet of the power tool. Accessories that do not
match the mounting hardware of the power tool will run
out of balance, vibrate excessively and may cause loss
of control.
f. Mandrel mounted wheels, sanding drums, cutters
or other accessories must be fully inserted into
the collet or chuck. If the mandrel is insufciently
held and/or the overhang of the wheel is too long, the
mounted wheel may become loose and be ejected at
high velocity.
g. Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, sanding drum for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of
the rotating accessory and run the power tool at
maximum no-load speed for one minute. Damaged
accessories will normally break apart during this test time.
h. Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments. The eye protection must be capable of
stopping ying debris generated by various operations.
The dust mask or respirator must be capable of
ltrating particles generated by your operation.
Prolonged exposure to high intensity noise may cause
hearing loss.
i. Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of
workpiece or of a broken accessory may y away and
cause injury beyond immediate area of operation.
j. Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord. Cutting accessory contacting a “live” wire
may make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
k. 
the start-up. The reaction torque of the motor, as it
accelerates to full speed, can cause the tool to twist.
l. Use clamps to support workpiece whenever
practical. Never hold a small workpiece in one
hand and the tool in the other hand while in use.
Clamping a small workpiece allows you to use your
hand(s) to control the tool. Round material such as
dowel rods, pipes or tubing have a tendency to roll
while being cut, and may cause the bit to bind or jump
toward you.
m. Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the spinning
accessory.
n. Never lay the power tool down until the accessory
has come to a complete stop. The spinning
accessory may grab the surface and pull the power
tool out of your control.
o. After changing the bits or making any adjustments,
make sure the collet nut, chuck or any other
adjustment devices are securely tightened. Loose
adjustment devices can unexpectedly shift, causing
loss of control, loose rotating components will be
violently thrown.
p. Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into
your body.
q. Regularly clean the power tool’s air vents. The
motor’s fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
r. 
materials. Sparks could ignite these materials.
s. Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, sanding band, brush or any other
accessory. Pinching or snagging causes rapid stalling
of the rotating accessory which in turn causes the
uncontrolled power tool to be forced in the direction
opposite of the accessory’s rotation.
For example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is entering
into the pinch point can dig into the surface of the material
causing the wheel to climb out or kick out. The wheel may
either jump toward or away from the operator, depending on
direction of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
a. 
your body and arm to allow you to resist kickback
forces. The operator can control kickback forces, if
proper precautions are taken.
b. Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing have
a tendency to snag the rotating accessory and cause
loss of control or kickback.
c. Do not attach a toothed saw blade. Such blades
create frequent kickback and loss of control.
d. Always feed the bit into the material in the same
direction as the cutting edge is exiting from the
material (which is the same direction as the chips
are thrown). Feeding the tool in the wrong direction
causes the cutting edge of the bit to climb out of the
work and pull the tool in the direction of this feed.
9

Yapay zeka ile Dremel Stylo+ 2050 kılavuzunuzla sohbet edin

Dremel Stylo+ 2050 kılavuzunuzdan yapay zeka ile anında yanıt alın

Dremel Stylo+ 2050 hakkında istediğinizi sorun. Yanıtlar bu kılavuzdan gelir ve dayandığı sayfalar belirtilir.

Stylo+ 2050 Bakim Takvimi

Düzenli
Hava girişlerini ve anahtar kollarını temizleyin

Sıkıştırılmış kuru hava kullanarak hava çıkışlarını ve anahtar kollarını yabancı maddelerden arındırarak temiz tutun. Kesici nesneler sokmayın.

Kilavuzda goster (12. sayfa)
Her kullanımdan önce
Aksesuarları hasar için kontrol edin

Her operasyondan önce taşlama tekerleklerini çentik ve çatlaklar, zımpara silindirlerini yırtık veya aşınma, tel fırçaları ise gevşek teller açısından kontrol edin.

Kilavuzda goster (9. sayfa)
M: QW-35-FL

Soru Sor Soru

0/1000

Stylo+ 2050'i önerir misiniz?

Evet Hayır
0
User Pic

Benoît Hamel

8 ay önce

Mandren kilit düğmesi bana kullanışsız geliyor. Cihazı kapatırken, güç düğmesiyle birlikte yanlışlıkla ona basıyorum ve bir gıcırtı sesi geliyor. Bu normal mi, ve bunu nasıl önleyebilirim?

0
User Pic

Manual.ly

8 ay önce

Mandren kilitleme anahtarı güç düğmesinin tam karşısında konumlandığı için, ikisine aynı anda basmak kısa bir mekanik sese neden olabilir. Bunu önlemek için cihazı kapatırken mandren kilidinin devrede olmadığından emin olun: önce gücü kapatın, sonra diğer elinizle kilidi bırakın (veya parmaklarınızın iki düğmede de olmaması için kısa bir ara verin). Bundan sonra normal çalışmaya devam edin. Eğer iki düğmeye aynı anda basmamaya dikkat ettiğinizde bile ses devam ederse, anahtar çevresini temizlemeyi deneyin ve gözle görülür herhangi bir engel olup olmadığını kontrol edin. Eğer hala devam ediyorsa, cihazı inceleyebilmemiz için lütfen kısa bir video ile destek ekibiyle iletişime geçin.

M: OA-GPT-5-NAN
M: OA-GPT-5-NAN

Sıkça Sorulan Sorular

A

Gravür, parlatma, zımparalama, oyma, temizleme ve hafif kesim gibi ayrıntılı işler için en uygundur. İnce yapısı, gücün değil hassasiyetin önemli olduğu durumlarda özellikle kullanışlıdır.

Bu yanıt yardımcı oldu mu?

A

Evet, bu sürüm aksesuarlarla birlikte gelir ve böylece çeşitli küçük projelere hazırdır. Dahil edilen araçlar, kullanımını yalnızca temel bir taşlama makinesinin ötesine taşır ve daha yaratıcı uygulamaları destekler.

Bu yanıt yardımcı oldu mu?

A

Evet. Alet değişken hız kontrolüne sahiptir, böylece performansı malzemeye ve işe göre ayarlayabilirsiniz. Düşük hızlar parlatma için; yüksek hızlar daha sert malzemeler için uygundur.

Bu yanıt yardımcı oldu mu?

A

Evet. Konik, kalem benzeri tasarımı kontrol ve konfor için yapılmıştır. Elde doğal bir his verir ve küçük yüzeylerde hassas, yönlendirilmiş hareketler için idealdir.

Bu yanıt yardımcı oldu mu?

A

Uygun göz ve toz koruması kullanın, aşırı baskı uygulamaktan kaçının ve aksesuarların güvenli şekilde takıldığından emin olun. Ayrıca hasarı önlemek için malzemeye uygun hızı seçin.

Bu yanıt yardımcı oldu mu?

A

Ağır taşlama işlemlerinden ziyade hassas ve hafif işler için daha uygundur. Zorlu malzeme kaldırma işleri için daha büyük ve daha güçlü bir alet daha iyi bir seçim olur.

Bu yanıt yardımcı oldu mu?

M: GO-GEM-FL-25

Avantajlar ve Dezavantajlar

Avantajlar

  • İnce kalem tarzı tutuş, detaylı işleri daha kolay ve rahat hale getirir.
  • Değişken hız kontrolü, farklı malzemelere ve işlere uyum sağlamaya yardımcı olur.
  • Parlatma, oyma, zımparalama ve gravür için birden çok aksesuarla uyumludur.
  • Hafif yapısı, daha uzun projelerde yorgunluğu azaltır.
VS

Dezavantajlar

  • Ağır hizmet taşlama veya agresif malzeme kaldırma için ideal değildir.
  • En iyi sonuçlar, dikkatli hız seçimi ve hafif bir dokunuş gerektirir.
  • Bazı aksesuarların doğru şekilde takılması ve dengelenmesi pratik gerektirebilir.
  • Toz, gürültü ve güvenlik önlemleri kullanım sırasında hâlâ önemlidir.
M: GO-GEM-FL-25

Ürün Özellikler

Tip

Düz taşlama makinesi

Güç

9W (230V)

Boşta devir hızı

5.000-22.000/dak

Takım tutucu

0,8-3,2mm hızlı serbest bırakma mandreni, pens

Özel özellikler

Hız ayarı

Ağırlık

110g

Teslimat kapsamı

15 parçalı aksesuar seti

M: GO-GEM-FL-25

Ürün Açıklama

Dremel Stylo+ Elektrikli Düz Taşlama Makinesi ve Aksesuarlar (2050-15)

Dremel Stylo+ elektrikli düz taşlama makinesi, ince ve kolay tutulabilir bir formda hassasiyet arayanlar için tasarlanmıştır. Kalem benzeri gövdesi, özellikle kuvvetten çok kontrol gerektiren detay işleri için elde doğal bir his verir. Kutudan çıkan aksesuarlarla birlikte bu kompakt araç; parlatma, temizleme, oyma, zımparalama, gravür ve hafif kesim işlerinizde esnek bir yardımcıya dönüşür.

Büyük çok yönlülüğe sahip küçük bir araç

Stylo+'ın en çekici yanlarından biri, ne kadar ulaşılabilir hissettirdiğidir. Hantal bir gövde yerine, hassas ve yönlendirilmiş hareketleri destekleyen konik bir tasarım sunar. Bu da onu hobi projeleri, el işi sonlandırma işleri, model çalışmaları ve narin tamiratlar için akıllı bir seçim yapar. Değişken hız kontrolü, aracı malzemeye ve göreve göre uyarlamanıza izin vererek kullanışlılığı bir üst seviyeye taşır.

Detaylı çalışmalar için tasarlandı

Kutudaki kullanım kılavuzu, doğru hız seçimi ve güvenli kullanımın önemini vurgular; bu da aracın amacını açıkça ortaya koyar: hafif bir dokunuşla kullanıldığında en iyi performansı vermek üzere yapılmıştır. Taşlama makinesi, çeşitli Dremel aksesuarlarıyla çalışır ve mandren sistemi aksesuar değişimlerini daha hızlı ve kolay hale getirir. Daha hassas bir tutuş isteyen kullanıcılar için pens sistemi de mevcuttur. Bu esneklik, keçeli parlatma uçları, zımpara tamburları, kesiciler veya gravür uçları arasında geçiş yaparken gerçek bir avantaj sağlar.

Günlük kullanımda pratik performans

Özünde Stylo+, kullanım kolaylığı ve kontrol ile ilgilidir. Hafiftir, kullanımı kolaydır ve el yorgunluğunun önemli olduğu uzun seanslar için uygundur. Aracın hız aralığı, iş parçasına uyum sağlamaya yardımcı olur: düşük hızlar parlatma ve hassas malzemeler için daha iyiyken, yüksek hızlar ahşap, metal, cam ve şekillendirme işleri için uygundur. Bu da onu farklı yüzeyler ve teknikler arasında geçiş yapan üreticiler için güvenilir bir seçenek haline getirir.

Güvenlik ve bakım önemlidir

Her döner alet gibi, Stylo+ da dikkatli kullanımı ödüllendirir. Kılavuz; koruyucu gözlük, toz koruması ve aksesuarların doğru şekilde takılmasını temel gereklilikler olarak vurgular. Ayrıca, aksesuarın işi yapmasına izin vermek için aşırı baskı uygulamaktan kaçınılmasını hatırlatır. Düzenli temizlik ve doğru saklama, zaman içinde sorunsuz çalışmasına yardımcı olur.

Notlar

  • En iyi sonuçlar, doğru aksesuar ve hızın seçilmesiyle elde edilir.
  • Nazik bir dokunuş doğruluğu artırır ve aşınmayı azaltır.
  • Toz veya kıvılcım oluşabilecek durumlarda uygun koruma kullanın.

Kısacası, Dremel Stylo+ hassasiyet odaklı projeler için şık bir çözümdür. Taşınabilirlik, kontrol ve aksesuar esnekliğini; detaylı yaratıcı işler için çok uygun hissettiren bir formatta birleştirir.

M: GO-GEM-FL-25

© Copyright 2026 Manual.ly