Manual.ly Logo

sera UVC-Xtreme 800 Kilavuz

0,0 · 0 Puanlar

PDF kılavuzu · 90 Sayfa

Türkçe

M: GO-GEM-FL-25
sayfa

/ 90

Loading...
781d6a9054693a344975a2f7322d15035812 page 11
17
Maintenance and care
Cleaning (every 4 – 12 weeks)
Over time and depending on biological load, food amount and aquarium
volume, mechanical and biological lter media get clogged more or less
quickly. Due to increasing sedimentation, the turnover through the lter
is reduced.
For cleaning, please rst pull the barrel plug from the lter head (6.5)
and then close the valves by turning the taps by 90° perpendicular to
the ow direction (6.4).
Now open the 4 holder clips (8.1 – 8.2). This leads to pressure release,
and you can now unscrew the valves from the lter head without water
running out (7.6). Now take the lter head off and lay it aside, or put it
back if you wish to carry it to a sink or the location where you wish to
clean the lter media.
You can now take the lter media baskets (1.34) out from above and
wash out the lter materials. It is best to use aquarium water for wash-
ing them out since this, unlike tap water, does not endanger the lter
bacteria. Never replace the lter material entirely but always retain used
lter material. By doing so, the lter bacteria will then spread over the
entire lter material again. Newly setup lters can also be activated by
using used lter material.
Maintenance of the running unit (every 3 – 9 months)
Please check the bottom side of the lter head whether the running unit
can move freely. To do so, please remove the two 90° elbows and the
pump chamber cover. Turn the rotor with your ngers. You should be able
to turn it without suspicious resistance. Rinse the openings thoroughly
with a water beam, depending on deposits and biolm, and re-assemble
the lter (4.1 – 4.7).
Possible problem sources and solution
Problem Possible cause Possible solution
E1 Suction pump does not ll up the
lter
E1.1 Are “IN” and “OUT” valves/hoses mixed up?
Check if bubbles are coming out of the intake strainer while suction
pump is in operation.
Yes, switch “IN” and “OUT” valves/hoses.
Make sure that the valve marking corresponds with the valve connector marking
(7.3).
No, see item E1.2
E1.2 Are “IN”/“OUT” valves still closed? Yes, open taps (6.4) of the “IN”/“OUT” valves.
No, see item E1.3
E1.3 Did you forget to insert the lter head seal (1.31)?
Yes, insert the lter head seal.
No, see item E1.4
E1.4
Are hoses laid out in a loop?
Yes, lay the hoses out without loops, shorten them if applicable.
No, see item E1.5
E1.5 Is the lter in operation for the rst time? Yes, ll the lter canister with water by two thirds. Then press “S”.
No, see item E1.6
E1.6
Dirt particles in the outlet valve?
Yes, remove the valve, clean it, and re-assemble.
No, see item E1.7
E1.7 Too low water level of the tank (e.g. terrapin tank)? Yes, press “S” button (2) repeatedly after suction is completed, or raise the
performance setting by pressing the “+” button. The setting can be adjusted as
desired once the air trapped inside the lter has escaped.
No, see item E1.8
E1.8 Is the spray bar too deep underneath the water surface? Yes, install the spray bar parallel to water surface, 15 cm (6 in.) underneath it at the
maximum (7.1).
No, see item E5, or please contact your retailer.
E2 Pump does not work E2.1 Power supply interrupted? Check mains and 5.5 mm (0.2 in.) barrel
plugs.
Yes, connect to power supply.
No, see item E2.2
E2.2 Are the valves still closed? Yes, open valve taps (6.4).
No, see item E2.3
E2.3 Is the rst LED ashing (green)? Yes, exit standby mode by pressing the “+” button (2).
No, see item E2.4
E2.4 Are the rst and second green LEDs ashing at the same time? Yes,
– disconnect the lter from the mains supply and reconnect it; or
– disconnect the lter from the mains supply, open the lter head (8.1 – 8.2). Clean
the lter head, in particular the rotor (3), so the rotor can rotate freely.
No, see item E2.5
E2.5 Too much air in lter? Yes, see item E5 of the chart.
No, please contact your retailer.
E3 Pump performance has strongly
decreased
E3.1 Are the valve taps (6.4) not in the correct “OPEN” position? Yes, open the valve taps properly so both handles are parallel to the longitudinal axis
of the valves.
No, see item E3.2
E3.2 Hoses bent, polluted or covered with biolm layers? Is there an
obstacle in the tubing?
Yes, clean/brush hoses and tubing, remove biolm inside the hoses by means of a
hose brush. Remove obstacles in the tubing.
No, see item E3.3
E3.3 Intake strainer or outlet clogged? Yes, clean strainer or outlet and remove coarse dirt.
No, see item E3.4
E3.4 Too much air trapped inside the lter? Yes, press “S” key (2) until pump works properly, repeat as required.
No, see item E3.5
E3.5 Too many devices connected to lter? Yes, prelters, T pieces, UV-C lamps etc. additionally connected to the intake or
outlet reduce the ow rate. The UVC-Xtreme lter already contains a suitable UV-C
lamp.
No, see item E3.6
Replacing the UV-C lamp (every 1 – 1.5 years)
Should the blue LED indicator lamp stay off, or if the UV-C lamp is
1.5 years old at the maximum, it needs to be replaced. First switch off
the lter head for replacing the lamp. Pull the barrel plug from the lter
head (6.5). Then you can disconnect the head from the lter (8.1 – 8.2).
Unscrew the union nut of the UV-C intake nozzle after having removed
the magnetic contact (1.18, 9.1/9.2), then pull the two 90° elbows at-
tached to the nozzles (9.3).
Now the union nut of the UV-C nozzle can be unscrewed (9.4). Pull the
nozzle off upwards. The quartz glass cylinder is located underneath.
It can now be pulled off, granting access to the lamp (9.5). The UV-C
lamp can be removed from the socket by pulling it gently. It can now be
replaced with a suitable replacement lamp. Then re-assemble the lter
in reverse order (9.6 – 9.1).
Switch-off protection: UV-C radiation is dangerous. Irradiation of
eyes and skin must be strictly avoided. The lters are constructed
according to latest safety standards in a way that a magnetic switch
switches off the UV-C lamp as soon as the lamp casing is opened.
Prior to every maintenance measure, the magnetic contact should
be removed rst before removing the two clickable 90° elbows, as
this will prevent possible eye or skin damage caused by UV-C radia-
tion being released from the now opened connection of the two 90°
elbows at the UV-C tube, in case disconnecting the device from the
mains supply was forgotten.
000000-00_sera UVC Xtreme 800_1200_INT_GBI.indd 17 07.09.2017 08:12:35

Yapay zeka ile sera UVC-Xtreme 800 kılavuzunuzla sohbet edin

sera UVC-Xtreme 800 kılavuzunuzdan yapay zeka ile anında yanıt alın

sera UVC-Xtreme 800 hakkında istediğinizi sorun. Yanıtlar bu kılavuzdan gelir ve dayandığı sayfalar belirtilir.

UVC-Xtreme 800 Bakim Takvimi

Bakim zamani geldiginde bana hatirlat
Her 4 haftada bir
Filtre medyasını temizle

Bakterileri korumak için mekanik ve biyolojik filtre malzemelerini akvaryum suyuyla yıkayın. Tüm malzemeyi aynı anda değiştirmeyin.

Kilavuzda goster (17. sayfa)
Her 6 ayda bir
Çalışma ünitesini bakım yapın

Rotorun elle serbestçe dönüp dönmediğini kontrol edin ve biofilm veya tortuları gidermek için açıklıkları su akışıyla durulayın.

Kilavuzda goster (17. sayfa)
Her 9 ayda bir
UV-C lambayı değiştirin

Tam işlevi sağlamak için gösterge ışığı yanıyor olsa bile amalgam lambayı en fazla 1,5 yıl sonra değiştirin.

Kilavuzda goster (17. sayfa)

Ucretsiz bakim hatirlatmalari

Satın alma tarihinize göre zamanlanır. Her zaman ücretsizdir, istediğiniz zaman abonelikten çıkabilirsiniz.

Göndererek gizlilik politikasını kabul etmiş olursunuz. Herhangi bir e-postada tek tıklamayla abonelikten çıkabilirsiniz.
M: QW-35-FL

Soru Sor Soru

0/1000

UVC-Xtreme 800'i önerir misiniz?

Evet Hayır

Sıkça Sorulan Sorular

A

UV-C ünitesi, filtre medyasından geçtikten sonra suyu ışınlayarak patojen ve yüzen alg azaltma için tasarlanmıştır. Sistem bir akvaryumu sterilize etmek için tasarlanmamıştır ve medyadaki faydalı bakteriler büyük ölçüde etkilenmeden kalır.

Bu yanıt yardımcı oldu mu?

A

Orta performans seviyesiyle başlayın ve tank boyutunuza, alg veya patojen yoğunluğunuza göre ayarlayın. Daha düşük sirkülasyon, suyun UV-C ünitesinde geçirdiği süreyi artırır, bu da azaltmayı iyileştirebilir. Hava sıkışmışsa veya akış zayıf görünüyorsa, kısa süreliğine artırın.

Bu yanıt yardımcı oldu mu?

A

İlk çalıştırma sırasında, sıkışan hava rotor alanına ulaşabilir ve gürültüyü artırabilir. Filtre kafasının altındaki havayı gidermek için emiş pompası işlevini kullanın. Birkaç dakika sonra, hava akışı stabil hale geldiğinde gürültü tipik olarak azalır.

Bu yanıt yardımcı oldu mu?

A

Mekanik ve biyolojik medya, biyoyük, yemleme ve akvaryum hacmine bağlı olarak yaklaşık her 4 ila 12 haftada bir kontrol edilmeli ve temizlenmelidir. Sirkülasyon azalırsa, yalnızca gerekli olanı temizleyin ve tüm medyayı aynı anda değiştirmekten kaçının.

Bu yanıt yardımcı oldu mu?

A

Lamba ömrü anahtarlama döngülerine bağlıdır, ancak servis kılavuzu yaklaşık 1 ila 2 yıl olduğunu belirtir. Özellikle UV-C göstergesi normal çalışmayı göstermiyorsa, tam performansı sağlamak için lamba yaklaşık 1.5 yıl sonra değiştirilmelidir.

Bu yanıt yardımcı oldu mu?

A

GİRİŞ/ÇIKIŞ valflerinin tamamen açık olduğundan, hortumların bükülmediğinden ve medya sepetlerinin tıkalı olmadığından emin olun. Rotorun serbestçe hareket edebildiğini ve aşırı sıkışmış hava olmadığını da doğrulayın. Sorun devam ederse, çıkış yolunu kontrol edin ve bir satıcıyla iletişime geçin.

Bu yanıt yardımcı oldu mu?

M: GO-GEM-FL-25

Avantajlar ve Dezavantajlar

Avantajlar

  • Sabit performans ve daha yüksek emisyon potansiyeli için entegre açılıp kapatılabilen amalgam lambalı UV-C
  • Akışı, enerji kullanımını ve UV maruz kalma süresini ayarlamak için çoklu ayarlara sahip düşük voltajlı, düşük sesli motor
  • Elektrikli emiş pompası, kurulum veya bakımdan sonra sıkışmış havayı tahliye ederek sessiz çalışmaya yardımcı olur
  • 360 derece dönebilen valfler ve eksiksiz bağlantı kiti, kurulum ve kullanımı kolaylaştırır
  • Uzun servis aralıklarıyla mekanik ve biyolojik filtrelemeyi destekleyen optimize edilmiş medya sepeti akış yolu
VS

Dezavantajlar

  • Dikkatli UV-C güvenlik kullanımı ve sadece orijinal yedek amalgam lambaları gerektirir
  • Filtre medyası veya hortumlar tıkanırsa veya hava akışı engellenirse performans düşer
  • Sızıntıları ve hava sorunlarını önlemek için doğru sızdırmazlık, dik yerleşim ve uygun GİRİŞ/ÇIKIŞ bağlantıları kritik öneme sahiptir
  • Servis görevleri (rotor ve UV-C bakımı) dikkatli yapılması gereken demontaj içerir
M: GO-GEM-FL-25

Ürün Özellikler

Tip

UV-C arıtıcı harici filtre

Akış hacmi

840 L/h

Akvaryum boyutu

100-800 L

Güç tüketimi

24 W

Özellikler

UV-C lamba, giriş/çıkış seti dahil

M: GO-GEM-FL-25

Ürün Açıklama

sera Professional UVC-Xtreme 800 Dış Filtre

sera Professional UVC-Xtreme 800 Dış Filtre, UV-C desteğini ve elektronik kontrolü, tatlı su akvaryumları için tasarlanmış verimli, düşük sesli bir dış filtreleme sistemine getiriyor. Esnek kurulum için tasarlanan bu filtre, su sirkülasyonunu tank boyutuna, biyoyüke ve istediğiniz UV-C arıtma yoğunluğuna uyacak şekilde ayarlamanıza olanak tanıyan, çoklu performans seviyelerine sahip modern bir düşük voltajlı motor kullanır. Enerji tasarrufu modunda, düşük watt ile çalışırken ihtiyaç duyulduğunda güçlü sirkülasyon sağlayabilir.

Xtreme serisini diğerlerinden ayıran şey, kontrol panelinden açılıp kapatılabilen entegre UV-C ünitesidir. UV-C amalgam lambası, çalışma sıcaklığı aralığında stabilize edilmiş çıkış sağlar ve patojenleri ve yüzen algleri birçok geleneksel UV-C lambasından daha etkili bir şekilde azaltmayı amaçlar. Gerçek sterilizasyonu hedeflemek yerine, sistem patojen azaltmaya odaklanırken, esas olarak filtre medyasında yaşayan faydalı filtre bakterilerini korur.

Su, optimize edilmiş medya sepetlerinden yukarıdan aşağıya doğru akar. Yivli bir sünger kaba parçacıkları yakalamaya yardımcı olurken, ince ve biyolojik medya seçimleri (örneğin, seramik biyomedya) mekanik ve biyolojik filtrelemeyi destekler. Medya geçtikten sonra, mekanik ve biyolojik olarak ön işlemden geçirilmiş su UV-C bölgesine çekilir, ardından ÇIKIŞ valfi aracılığıyla akvaryuma geri döndürülür. Sistem ayrıca, kurulum veya bakımdan sonra sıkışmış havayı gidermeye yardımcı olan, sessiz ve güvenilir çalışmayı destekleyen bir elektrikli emiş pompası da içerir.

Güvenli ve doğru kullanım için, balastı kurarken, filtreyi yerleştirirken ve UV-C bileşenlerini kullanırken sera Professional UVC-Xtreme 800 Dış Filtre Kılavuzu'nu dikkate alın. Ünite iç mekan kullanımı için tasarlanmıştır, yeterli su akışı gerektirir ve bakım sırasında UV-C maruziyetini önlemek için güvenlik önlemleri içerir.

Temel sonuçlar

  • Patojen ve yüzen alg azaltma için açılıp kapatılabilen kontrol ile UV-C özellikli dış filtreleme
  • Sirkülasyonu, UV maruz kalma süresini ve enerji kullanımını dengelemek için çoklu motor performans seviyeleri
  • Temizlik sonrası daha sorunsuz başlangıçlar için entegre hava tahliye rutini
  • Uzun servis aralıklarını desteklemek için optimize edilmiş akış yolu ve medya sepetleri
  • Esnek kurulum için kolay 360 derece valf yönlendirmesi ve dahil bağlantı kiti

Notlar

  • Faydalı bakterileri korumak için kısmi medya temizliğini ve yerleşik medyanın yeniden kullanımını tercih edin.
  • UV-C amalgam lambaları tipik olarak, ünite kılavuzuna uygun olarak bir servis döngüsünde (anahtarlamaya bağlı olarak yaklaşık 1 ila 2 yıl) değiştirilir.
  • Akışı ve verimliliği korumak için doğru sızdırmazlığı, dik yerleşimi ve doğru GİRİŞ/ÇIKIŞ tesisatını sağlayın.
M: GO-GEM-FL-25

© Copyright 2026 Manual.ly